Hi I running Solaris 10 on ULTRA 10 installed.I want to configure D1000 with ULTRA 10.I inserted scsi diff card(x6541) in slot.I hooked up D1000 with Ultra 10, but the system does't see disk array. I tried with devfsadm amd boot -rv. THANKS.......... ...

Hello Support, I have a Sun Ultra 10 used as a workstation for medical equipment/applications. Every morning when it is turned on, it begins to boot up and gives a Boot Failure message for a:. All I do is cycle power and unit comes up correctly. What could be causing this?, Bad sector on ...

I'm trying to figure out what tile cut-out size to use in my data center for these servers. Is the whole bottom open?

hi people... at first, sorry for my english. I hava a Sun Fire 280R with Solaris 8 and today it boot aparently without a reason, it boot 5 or 6 times. The error before the fall is: WARNING: Uncorrectable error detected by pci0 (safari id 00000000.00000008) during DVMA read transaction ...

Hi! Since yesterday evening the box does not want to start up. It seems that I can access the BIOS and when I look at the DMI info, the only thing I see is a lot of entries with a date and then this very bad message "System rear fan1 fault" I already downloaded supplemental disk ...

We are custom keyboard designers, and we manufacture a variety of Sun compatible Type 5 & 6 keyboards. I need to test the function of the Compose LED on a USB keyboard, and have a Blade 100 running Solaris 9. I can't get the Compose LED to light (even on a branded Sun keyboard), using ...

Hello I'm trying to add a third SCSI drive to the W2100z. The first is a 73GB Seagate, the second is a 147GB Seagate and the third is a 147GB Fujitsu. The first (ID 1) and the second (ID 0) are on the same connector connected to the B channel. The third (ID 0) is on the A channel. When ...

When I logout of an Xsession (gnome/kde/fvwm2) the system hangs (power cycle required) fairly often. This happens when using the nv or nvidia (x86_64-1.0-7667) drivers and kdm or gdm. When I'm using the nvidia driver, after the logout the nvdia splash screen stays permanently up. This ...

I am trying to get some data off of some tapes that span two volumes. I put in the 2nd tape and it says wrong dump date and proceeds not to read it. The volumes seem to cross the day boundary. First volume starts at 10pm next one is 12:45am the next day. Does anyone know of a way to get ...

Hi.Recently I decided to buy a notebook, and due to there is no point to play games on that "low-life-battery" thing, thus I was wondering if there are any sort of Sun notebooks?Or at least any notebook which can support Solaris with all the hardware working perfectly strait out of the ...

In one datacenter we have a terminal from IBM that works without any problems on our Sun-servers, but we also we have a terminal from Wyse. This terminal has a slight problemen, because someone start playing with the settings. I tried to set the setting back as found for the serial console, but ...

Hi All, We have a v20z which had a mirrored array configured. One disk failed and now we are having problems installing a replacement. The LSI BIOS gives an incompatible partition error when we try to set the disk from the original array as the primary.. Help please... Thanks Sidney ...

I have Solaris 9 installed on a netra t1 105 which goes into half every night. I have turned off the power management and the logs in /var/adm/messages does not show anything unusual. <div class="pre"><pre>Oct 19 14:16:25 dev-sol9 pseudo: [ID 129642 kern.info] ...

Hello. Is it possible to take the video card from a Sun system and install it in a PC? It has VGA hookups. Someone mentioned the BIOS on the video card being stamped with Sun information, so it wouldn't work. I know nothing about Sun stuff, but I wasn'y quite ready to take his word. ...

Hi.I am looking for information about RAM disks. How big they are, costs, performance etc. Where can i find such information. Is there somebody here, which have information about RAM disks (virtual disks).My problem is that i need big disks (70 - 80 GB) and need real fast access.Reg ...

Is there a way to go back through the configuration wizard that is launched on pre-installed machines shipped from solaris? We have recieved a v20z server. The steps we took include: Setting the SP to DHCP, logging in through a SSH client, creating a manger username and password by typing ...

I want to mount (14) Netra 240's in a single cabinet if possible. I need redundant power. Looking at the power specs for the 240's, it appear they have a max draw of about <a href="mailto:3A&#64;220V." target="_blank">3A@220V.</a> The 900 & 1000 Series cabinets ...

I have a sun netra 240 which currently has one 72GB disk, I am adding an extra 72GB disk, my question is do I need to power down the server to insert the new disk or can I insert it while power is on ?

Added 2nd 3510 array via daisy chain to existing 3510. First one has been in operation, now after adding the second one the OS does not see the new LUNS. One logical drive 4.2 TB with 5 partitions each under 900 GB. Thought that maybe a reboot -- -r might fix it, but not true. Mapped the LUNS ...

I have a customer who wants to use a USB external DVD drive to upgrade software a lot of Sunblade 150 workstations. The machines have internal CDROMs but he doesn't want to change all for DVDs. He wants to know if the addonics AEPDVRW888UM is compatible with these machines ie will it work on ...

The Sun Multithreaded 10GbE Networking Card does not have drivers available on Sun's site for either Solaris or Linux.The user manual is ...

Don't know if this is a right place, if it's not, please direct me, thanks!I had a SPARC Ultra 10 machine running under Solaris 10, it wasrunning for couple months. Recently when I reboot it, it was hang at"Use is subject to license terms."I press STOP+A to bring me to ok prompt, then type ...

After downloading Sun XVR-500 Graphics Accelerator Driver with Sun Download Manager, it is impossible to extract the file. The download manager shows a file conflict error. Trying to extract the zip-file with winzip, it shows a problem with extracting the install script. There is a problem ...

hello.I'm new in sun solaris....yesterday i have download solaris 10...i came from windows ....i try to install solaris in my pc ...but during installation process, i receved error message: 1)sistem time is not valid2)error memory becouse , memory is interleaved..what can i do for resolve ...

Can anyone help?I am trying to get a Cobalt RaQ 550 up and running for a project.As soon as power is applied the system fault spanner is lit. Upon power on no text is displayed on the LCD screen.Any ideas?Thanks

Hello,after an Firmware Upgrade from 4.12 to 4.15F the HTTP-Service responses with error 404.The service was inactive before the upgrade and activated a week after the upgrade was installed. I can't tell if the service ever worked like it should.Any suggestions what to ...

Can anyone help me avoiding Sun Cabinet FrameManager service LED on Sun Fire 4900 Rack.

FOr some reason my raq 4r will not display the virtual sites in the control panel.. instead, i get "The server encountered an internal error or misconfiguration and was unable to complete your request."Also, when sending and receiving email, i get this error. "Task 'mydomain.com - Receiving' ...

(just dreaming...)Here's what I want:(I know, "people in hell want ice water" :-) ) - Solaris x86 support for my SunPCi IIIpro card. I want to run both Solaris SPARC andSolaris x86 on my Sun SPARC workstation; - SunPCi 3.2x for x86 Solaris. I want to run Solaris x86 AND Windows (don't ...

Hi there,I have a sun fire v440 server. Recently, qlogic qla2300 card started to give "invalid nvram" error and i get replaced the card with a new one. But when i connect the card to system and power up no drivers see and attach the card. neither qla and qlc attach the hba. What can i ...

I'm trying to configure the Blade 1500 running Solaris 10 to use the DVi output. Still haven't got a signal.Anyone successfully do this? I followed suggestions for modifying the Servers file and adding :0Local local_uid@console root /usr/X11/bin/Xserver :0 -nobanner -dev /dev/fbs/pfb0a -dev ...

The T3 power supply has a green LED for AC power, but has a blinking amber LED for the PS LED. When we connect to the T3 it shows the battery status for this Power supply as unknown. We can't seem to figure out what the problem is. Any suggestions?Thanks,Glyn

I am having trouble getting my SunFire V240 system to show its graphics display through a AVO console monitor. I have tried numerous resolutions, but I keep getting this blue striped screen. Is there any good documentation, besides the guide which comes with the graphics cards. I need to get 3 ...

Hi,Greetings!I am an engineer from RVSI Inspection, NY, US. I need your support in configuring HP Deskjet 932c printer (parallel port) to Solaris 10 X86 machine. We are facing difficulties in printing ASCII documents on Solaris 10 x86 with default printer settings (Content types: simple; ...

Hello Everyone,I have HDS 9960 consolidated storage being used by hetrogenous servers through Mcdata Sperion 4500.I would like to introduce SUN Fire V440 in this enviornment.Please help me in choosing the RIGHT HBA for the same.Regards,Aarti

On Sun Ultra 5 workstation, does the audio device process 8k bytes per second?

Hi, I'm running a Sun Blade 150 with Solaris 8. I have a Sun Pci card with Windows 2000 loaded. When Win2k boots, it asks for drivers for a "sun floppy". I've looked around for these drivers but I can't find them. Can anyone point me to them. Thanks. ...

Hi All I'd like to know if anyone has racked a T2000 in an HP 10000 series rack.... I know that as long as the racks comply to EIA 310 then all should be ok, but I'd like so be safe Thanks

Hello, did anyone managed to use a storedge tape autoloader under red hat linux , maybe using bacula ? Thanks, Patrizio

In the document "Sun Gigaswift Ethernet Adapter Installation & User's Guide" there is a list of all the other models of Sun servers except 220R which can support the Gigaswift Ethernet VTP Adapter card. My colleague said that the 220R might support the card but due to it is ...

Hi, I'm a new useer in this forum and i need help to change my keyboard configuration. I've a SB1500 workstation on solaris 10 with an AZERTY keyboard. I change it by an QWERTY but when I use it, it still appear to be an AZERTY. How can I change the keyboard configuration... ? ...

Hi, does anyone know if I can install an external HP tape DAT72 StorageWorks on my SunFire 280R? Thanks!

Hello, how can I mount on a Windows / MAC OS X System an damaged diskimage for SunPC. Is there any change? Can I mount the diskimage on for Solaris to change some files in this diskimage. # Thanks alex ...

Can somebody please help me. I bought a refurbed GDM-5010pt two or three years ago. Probably two years ago. And it has been the best monitor i've had. How ever, around a month ago i had to retire it because the picture went wonky, it constricts the image in the center like an hour glass and ...

In my office somebody is sending a bulk packet continously. Our environment consist of NIS server for authentication and Cisco routers and switches.How can I trace the source of this packets ? What are the steps ? Thanks, Britto

Hey all, I would like to upgrade my workstation to the new Opteron 175 processor (with dual core goodness). Is the W1100Z capable of supporting such a processor. It is only sold with the maximum of an Opteron 150... Does anyone have any ideas? Iain ...

One of my L25's has been power cycled and after it starts initializing the following message appears: CHK 262F library.c Line 4529 Path 0000 The manual says "the X axis friction is too high for normal operation". Can this be dealt with or is it a harware call to Sun! ...

When booting this Ultra 60, it gets to the 'Initializing memory' message and it doesn't go any further. I can see the disk when I get to the 'ok' prompt and do a 'probe-scsi-all'. What kind of problem does this point to?

Hi, I'm having trouble updating the BIOS on a v20z. The update procedure fails with timeout: % platform set os state update-bios \ /mnt/sw_images/platform/firmware/bios/V1.34.4.2/bios.sp This command may take several minutes. Please be patient. Bios started Error. The operation ...

Can the UltraSparc III processor boards on a 15K server be swapped out and upgraded to the UltraSparc IV processor boards? Also, can MIXED processor boards be used on the 15K? In other words, can I use both UltraSparc III and IV boards on a 15k?If so what are the parameters? Are separate ...